|
E2
Elite Engineering's PCV Oil
Catch Can
|
|
  Designed
to fit C5 (1997-2004) and 2006+
C6 Z06 For
standard C6 Corvette
applications, click Here |
|
 |
|
|
 |
|
This is the PCV Catch Can that
everyone is talking about!
Featured in the Sept. 2009 issue
of
Corvette Fever
magazine
Click to
Read:
Purpose of your Stock PCV
System:
The PCV (Positive Crankcase
Ventilation) system is designed
to regulate and
remove fumes from the engine crankcase, and to alleviate crankcase
pressure which
could cause oil leaks or seal damage. The PCV system routes crankcase
fumes into
the intake manifold where they can be burned to eliminate harmful
emissions into
the atmosphere. The PCV valve controls the amount of crankcase flow
volume
depending on the engine's load. With large throttle openings (high
engine loads),
the more blow-by gases are produced, and the more the PCV system flows
oil vapor
in to the intake manifold. The PCV valve also functions as a check valve
to prevent
intake manifold flow from reversing back into the crankcase when there is
a
backfire, or during periods of high manifold pressure (boost) during
forced induction
by turbocharger or supercharger.
|
|
|
|
Negative Effects of your
Stock PCV System: |
Many
Corvette, Camaro, Firebird and
GTO owners with LSX
engines can
testify to the amount of
oil residue that can accumulate
inside the intake manifold,
throttle body, intake
track and even the air filter
during aggressive driving
conditions.
There are various
negative effects when excess oil
vapor contaminates the intake
system from the stock PCV
system - such as:
-
*Throttle
body and/or MAFS (Mass Air
Flow Sensor) malfunction or
failure.
-
*Air filter, intercooler (if
equipped) and intake ducting
contamination if oil pools
and run back out the intake
system after engine
shutdown.
-
*Reduced
octane of the air/fuel
mixture, which can cause
detonation and the ECM
(Engine Control Module) to
retard timing, thereby
reducing engine power.
-
*Excessive
carbon build-up on valves,
piston crowns, combustion
chambers and spark plugs.
This also increases the
chance of detonation and
power loss.
-
*Increased emissions &
possible contamination of
catalytic converters and
oxygen sensors.
-
Bottom
line: Excessive amounts of
oil vapor in the intake manifold
is detrimental to
your engine!
Solution: Install the
E2
Elite Engineering PCV Oil Catch
Can!
|
|
Installed on an
LS1 >
 |
|
Ultimate Function: |
The
E2 Elite Engineering PCV Oil Catch
Can is designed to effectively
separate oil from
the crankcase vapors, thereby eliminating all negative effects of
excessive intake
system oil contamination. Our Catch Can has been engineered to remove
the oil
vapor before it has a chance to contaminate your intake system.
Not all Catch Cans are
created equally!
Often
Imitated, never
duplicated. Most
Catch Cans on the market are
just comprised of an empty container with 2 ports. While that simple design
may trap a few oil droplets, our Catch Can is designed to condense the oil vapor and
trap the oil inside the container.
Our test proven design incorporates a stainless steel mesh and screening
mechanism
that acts like a maze to collect and condense the oil vapor. Once the
oil vapors
condense into liquid droplets, it falls to the bottom of the can. In
addition, the top
assembly is specially designed to keep any liquid from climbing out the
exit hole
during aggressive driving conditions. Stored oil volume is approximately
8
ounces. You will be amazed by how much oil our Catch Can will catch!
Don't settle for an inferior competitor's
product. Insist on Elite
Engineering's Catch Can! |
|
|
|
Premium Construction: |
The Elite Engineering PCV Oil
Catch Can is constructed of the
finest materials inside
and out. High performance car owners insist on the best products that
offer
unsurpassed function as well as impressive visual enhancement. Our Catch
Can does
both! Our exclusive design incorporates optimum function and the finest
materials,
construction and finish for maximum dependability.
The 2.6" diameter by 6.0" long body is machined from billet 6061-T6
aluminum alloy,
and then anodized in a variety of colors for a striking look. The
internal condensing
screen is stainless steel encased inside an aluminum alloy housing
designed for low
flow restriction. The housing can be disassembled for screen inspection,
cleaning or
replacement if needed. The inlet and outlet hose fittings are brass, and
threaded
into the body and sealed with Teflon tape. Supplied hoses are fuel and
oil vapor
compatible (SAE 30R7 rated). The bottom catch can reservoir screws onto
the top
of the unit, and is sealed with a built in O-ring. Inspection and
cleaning is easy by
simply removing the bottom of the unit without disturbing the mounting
system or
hoses.
In keeping with our high quality standards, all supplied mounting
hardware and
screws are stainless steel. The supplied custom machined mounting
bracket is black
anodized 6061-T6 aluminum, and is attached to the passenger side engine
head on
LS1/LS6/LS7/ applications with (2) two 10 mm button head screws.
Each Catch Can kit includes everything you need to install the system.
Basic
mechanical skills and common hand tools are the only things required.
For
More Pictures, click here
|
|
|
Kit Includes:
(Click
Here)
-
*Catch
Can assembly beautifully
anodized in choice of
available colors, complete
with 3/8" barbed
inlet/outlet hose fittings.
-
*Custom machined mounting
bracket for LS1/LS6/LS7/
applications, black
anodized.
-
*Stainless steel mounting
hardware.
-
*24
inches of 3/8" ID fuel and
oil vapor compatible hose.
-
*PCV
adaptor hardware.
-
*Black
zinc plated hose clamps.
|
We are offering
our Catch Cans in the (4) four
most requested
colors: Anodized in
Red,
Silver,
Black,
and Blue
|
|
Click here
for detailed Installation
instructions!
|
|
_________________________________________________________________________________________________________________________________________ |
| |
 Clear
(Silver)
Anodized Catch Can,
hardware, and mounting bracket
Selling Price = $169.50 shipped
in the USA.
|
|
Click to Purchase |
| |
|
___________________________________________________________________________________________________________________________ |
| |
 RED
Anodized Catch Can,
hardware, and mounting bracket
Selling Price = $169.50 shipped
in the USA.
|
|
|
|
Click to Purchase |
| |
|
_________________________________________________________________________________________________________________________________________ |
| |
 Black
Anodized Catch Can,
hardware, and mounting bracket
Selling Price = $169.50 shipped
in the USA.
|
|
|
|
Click to Purchase |
| |
|
___________________________________________________________________________________________________________________________ |
This
Color is Temporarily OUT OF
STOCK
|
Blue
Anodized Catch Can,
hardware, and mounting bracket
Selling Price = $169.50 shipped
in the USA. |
|
|
|
Click to Purchase
|
|
|
